By Lee Ann Brady, DMD 

For addressing the access hole of a screw-retained implant crown, my preferred method involves applying Teflon tape over the hole followed by temporary filling material, such as Telio Inlay from Ivoclar Vivadent. 

I emphasize to patients the importance of maintaining accessibility to the screw for potential adjustments without jeopardizing the integrity of the ceramic crown. Hence, immediately after seating the crown, I ensure no adjustments are needed before doing the filling. 

Patients are scheduled for a final post-op appointment with the surgeon after the restoration is in place. If there are no issues requiring crown removal, the Teflon tape and Telio Inlay may remain indefinitely, monitored during hygiene recall appointments. As long as the temporary filling remains intact, replacement is unnecessary. 

In cases where the Telio Inlay dislodges but the Teflon tape remains intact, I inform the patient of our plan to reapply the temporary filling. However, if repeated dislodgment occurs, leading to inconvenience, we consider transitioning to a permanent filling. In such instances, fresh Teflon tape is applied, and the access hole is filled with composite that precisely matches the crown’s color. 

Even if years pass and the Telio Inlay needs replacement, I opt for a temporary filling for ease of identification if removal is necessary. Only if frequent filling replacements prove bothersome do I consider switching to a permanent filling because I prioritize easy retrievability of the screw. 

By Lee Ann Brady, DMD 

One of the most common ways that we temporize a patient who is having maxillary anterior implant dentistry is with an Essix retainer. Some patients will wear it 24 hours a day and others for less. Hopefully they are taking it out to rinse, brush, and floss, but the reality is they are wearing a removable device that covers all of the tooth surfaces for a lot of hours every day, and we’re increasing their risk of caries, decalcification, and gingivitis. 

In addition to discussing the normal oral hygiene to be done at home, in our practice, we typically dispense a product like Clinpro 5000 from 3M or MI Paste from GC America. These are high calcium and fluoride products that provide fluoride treatments inside the Essex retainer. 

• If a patient is sleeping in the Essix, the instructions are to brush and floss the teeth and then use a toothbrush to spread a little bit of Clinpro or MI Paste on the inside of the retainer before going to sleep. 
•  If they are not wearing the Essix during sleep, the instructions are the same but to wear the Essix for up to an hour every evening before removing it to go to sleep. 

If the patient’s caries risk is high, I prefer using 10% carbamide peroxide gel instead of Clinpro or MI Paste. This is the active ingredient we us in perio trays to help prevent gingivitis. This is also the means by which patients can whiten their teeth while wearing an Essix retainer. 

To prevent damage to the Essix, instruct patients to rinse it with cold water and, when not wearing it, to store it in the provided container.  

Kelley Brummett, DMD 

After you do a crown preparation, do you tell your patients that you’re going to make them a temporary or a provisional?  

Provisionals are more than temporary restorations. They are part of a process. They’re the dress rehearsal to the final outcome. They are the prototypes for the final restorations.  

The “provisional” process is an opportunity to gain trust with the patient while modifying the length of teeth, the shape, or the color. It is also a way to communicate with the patient how their functional and parafunctional findings may have contributed to the destruction of their teeth. 

As the patient comes back to have their bite checked and to talk about what they like and don’t like, we are building trust. We’re involving them in understanding what they feel and think. We’re listening to improve their conditions. 

I’ve had patients who were fearful about moving forward with extensive treatment because they couldn’t envision the transition from the prep appointment to the final. What would those temporaries look like? What would they feel like? How would they function?  

So, when I am discussing a case with a patient, provisionals are all part of one treatment fee. We talk about the prep process, the provisional process, the lab process, and the final seating process—all as one process for which there is a fee. We discuss how the provisionals will guide us in optimizing the lab plan to achieve the desired comfort, function, and aesthetics.  

Whether it’s a single tooth or whether it’s multiple, I encourage you to help the patient understand that what you are providing in the interim between a preparation and a seat of a restoration is called a “provisional.” 

A provisional protects the underlying tooth structure. It keeps tissue in place. It helps the patient feel confident. It allows us to understand what might be going on functionally. It helps us communicate better with the lab. It’s more than a temporary restoration. It’s a guide on our journey toward predictable and appreciated relationship-based dentistry. 

Gary M. DeWood, DDS, MS 

Many dentists believe that provisional restorations don’t really matter. After all, they are not really a stand-in for the final restoration. I would respectfully disagree. I am a proponent of creating functional, durable, and highly esthetic provisional restorations, every time. They have the potential to impact your dental practice a lot more than you might think. Whether you print them, form them, or free-hand them, a GREAT temporary is a great billboard for your practice. 

1. Make the provisional as Esthetic as the final restoration.

I contend that the more your provisionals look like what you are hoping for when you seat the final restorations, the more people will talk about them, AND you. 

I was able to build a referral restorative practice by creating provisionals that made patients want to come to my practice and specialists want to send people. For much of our career, almost the entire team of the oral surgery office we worked with, and many of the team members from the other specialty practices we worked with, were our patients in Pemberville, Ohio. 

Front teeth or back teeth, when you make them look like teeth, people will like it and they will show and tell other people. “This is just the temporary?!” was not an uncommon question or exclamation from our patients.  

2. A GREAT guide makes a GREAT provisional restoration.

Your wax-up** cast/model serves as your vision, as your preparation guide fabrication device, and as your provisional former. When the preparation is appropriately reduced for the material selected, the temporary can mimic the restoration. 

** The wax-up might be created with wax then duplicated with impression material and stone to create a cast, or it might be scanned to be duplicated with resin and printed or milled to create a model. 

3. 3. Use that provisional to highlight the talents of your team members.

You might LOVE to make those provisionals, but if your assistant is equally excited when it comes to recreating nature for the patient to appreciate, then it could be an opportunity for patients to see that your assistant does much more than set-up, clean up, and hand you an instrument. My dental partner, Cheryl, (who is also my wife) and I actively sought out things that could help our patients experience our team as much more than our helpers. 

As we all know, dental assistants are an integral and vital part of what the practice is and are a powerful force in how and why patients ask for dentistry. Assistants who fabricate provisionals have an opportunity to be seen differently, and we were always looking for ways to create partnership with them in our treatment. 

4. 4. Take pictures of them.

Photographs of the temporary will make it easier for the lab to design the outcome. They will be able to see what you are thinking, able to visualize what you want, AND maybe even more importantly, see what you do not want. With anterior provisionals, I have frequently noted to my ceramist, “Please put the incisal edge in exactly this position vertically and horizontally in the face, then use your artistry to create the tooth that belongs in the face you see in the photographs of the patient before, prepared, and temporized.” 

There were many times when the technician was able to see and create effects that I might have not recognized as being “just the thing that would make these teeth extraordinary.” And don’t forget to show the patient the photograph. 

5. 5. Love the material you make the temporary with.

The better the provisional material is at holding tooth position and functional contact, the less adjustment we’re going to have, so using a high-quality material is important. There are a lot of them out there. I like bis-acryl materials that polymerize with a hard surface, have little or no oxygen inhibited layer, and can be polished easily. The polish is more about feeling smooth than about the shine. Ask you patients how their provisional tooth “feels” when you are done, so they sing your praises. 

6. 6. Use high-quality core material.

When you use a good core material the prep will be smoother, making it easier to fabricate nice provisionals. Ideal prep form goes a long way toward better provisionals. 

7. ASK your patient to tell people.

As noted above, when you can elicit an emotional response about the awesomeness of your provisional, ask the patient to tell other people, “….and this is just the TEMPORARY!” 

Kelley Brummett, DMD 

Resin-based temporary cements are wonderful due to their translucency and their ease of cleanup after light curing. My favorite is TempoCem from DMG.  

To prevent resin-based temporary cement from bonding to the newly placed composite, some dentists apply Vaseline on the prep before placing the provisional. 

Instead of Vaseline, I use glycerin. We keep glycerin in a little syringe in the room, and we put just a smidge in a little dapping dish so I can coat the top of the prep with it. Since beginning to use glycerin, I have not had difficulty retrieving bonded provisionals. 

If your provisionals come off, just get a new and stronger temporary cement. No! I am just kidding! If the provisional comes loose, it is often because you do not have enough space, so excursive interferences are high. When this happens, I engage with the patient in checking their occlusion, and continue to work out the determinants of their occlusion.  

Figuring these things out while the patient is in a provisional that is retrievable due to the ease of the temporary cement used, helps me continue to make progress on their occlusion before moving forward with the final restoration.  

It is not a failure of cement; it is a growth opportunity for discovery and patient engagement! 

Christopher Mazzola, DDS 

This is an example of a clinical study that can help us in our everyday practice of dentistry. Although the findings do not surprise us, keeping the findings in mind will guide us in decisions we make when performing treatments our patients are counting on to be long lasting. 

Dr. Markus Blatz is co-founder and past President of the International Academy for Adhesive Dentistry (IAAD) and Chairman of the Department of Preventive and Restorative Sciences and Assistant Dean for Digital Innovation and Professional Development at the University of Pennsylvania School of Dental Medicine in Philadelphia. He and a research team from the University of Coimbra, in Portugal, studied the effect of rubber dam isolation on bond strength to enamel. Their goal was to test two hypotheses. 

Hypothesis 1: Rubber dam isolation improves sheer bond strength independent of the adhesive system used. 

Hypothesis 2: A highly filled 3-step etch and rinse adhesive will provide higher bond strength values than an isopropyl-based universal adhesive. 

For their tests, they used OptiBond FL from Kerr for the 3-step etch and rinse adhesive and Prime & Bond Universal Adhesive for the isopropyl-based universal adhesive. 

The mesial, distal, lingual, and vestibular enamel surfaces of thirty human third molars were prepared (total n = 120 surfaces). A custom splint was made to fit a volunteer’s maxilla, holding the specimens in place in the oral cavity. Four composite resin cylinders were bonded to each tooth with one of two bonding agents (OptiBond FL and Prime & Bond) with or without rubber dam isolation. Shear bond strength was tested in a universal testing machine and failure modes were assessed. 

Both hypotheses were supported by the results reported in the Journal of Esthetic and Restorative Dentistry in November of 2022. 

• With the rubber dam in place, both of the adhesives performed better than without the rubber dam in place, resulting in approximately twice as much shear bond strength with the rubber dam. 
• The 3-step OptiBond FL system resulted in a more resilient bond than the Prime & Bond Universal adhesive. The OptiBond FL group with rubber dam presented the highest mean bond strength values. Fracture modes for specimens bonded without rubber dam isolation were adhesive and cohesive within enamel, while rubber dam experimental groups revealed only cohesive fractures. 

For the benefit of our patients, we shouldn’t cut corners that will impact the longevity of a restoration. My thoughts are that whenever we have basic pure enamel bonding it should be under a rubber dam, using a total etch, 3-step adhesive system. But considering dentin likes to be moist, we may need to make other clinical judgments.  

Laura Harkin, DMD, MAGD 

Let’s delve deeper into the preclinical interview! 

It’s helpful to understand a patient’s perception of their overall health and oral health, as well as what type of restorative dentistry they’re hoping to have and why they feel the way they currently do.  

Sometimes, an integral family member has influenced the timing of care. For instance, you may hear, “My grandchildren are making fun of my teeth” or “My wife asked me to get my teeth fixed.” From this response, I know that I will need to be sure my patient personally desires treatment before rendering it. I’m also anxious to understand what type of restorative dentistry a patient is considering. For example, are they open to removable prosthetics, fixed crown and bridgework, or implantology? 

Recently a new patient came to my office with an emergency. Tooth #5 presented with the buccal wall broken to the gumline and a moderate-sized, retained, amalgam filling. He immediately said, “I do not want bridgework.” I listened quietly until he elaborated by saying, “When I had this front tooth replaced by my other dentist, I had to take it in and out, and I just found that so irritating.”  

I finally understood that he was referring to a flipper but calling it bridgework. So, it’s important to listen and ask questions when someone seems close-minded about having a certain modality of treatment. Delve deeper into the conversation because it may simply be confusion surrounding dental terminology. 

For the grandparents who ask for a better smile, I’d like to understand their thoughts on the scope of treatment and their expectations. Are they looking for a white, straight, Hollywood smile or a more natural appearance with a little bit of play in the lateral incisors? Are they mainly concerned about stains, gaps, or a missing tooth? Are there other problems they’re aware of such as tooth sensitivity, inflamed gums, or the need for a crown? This input is very important as we continue conversation with co-discovery throughout the clinical exam, diagnostic records, and treatment planning phase. 

Learn to count on your chairside for pertinent information. 

I’m fortunate to always have my assistant, Cindy, beside me for preclinical conversations, comprehensive examinations, and restorative procedures. Sometimes, Cindy interprets a patient’s statement or component of conversation differently than me. She may hear a message that I missed or read body language of which I wasn’t aware. Sometimes, auxiliary conversations between patient and assistant take place after I’ve left the room to complete a hygiene check.  

At the end of the day or in the morning huddle, we always take time to discuss interactions with our patients. Together as a team, we’re more efficient at acquiring accurate information so that we may approach the road to health most effectively for each individual. 

Determine if trust is present. 

As I’m getting to know a patient and before I choose to begin restorative treatment, I seek to understand if trust is present in our doctor/patient relationship. New patients often share past dental experiences, and, unfortunately, some have lost trust in dentistry itself. This may be warranted due to improper care, but it may also be due to a lack of understanding or unclarified expectations regarding a given procedure or material choice.  

It’s not unusual, particularly when a patient is considering a large scope of treatment, to serve as a second or third opinion. Building trust and waiting to be asked for our skills are key necessities before moving forward in irreversible therapy.  

The comprehensive examination, periodontal therapy, splint therapy, and gathering of records are all appointments during which opportunities exist to get to know our patients. True trust often takes time to establish, but the reward reaped is frequently one of empathy, friendship, and the ability to do our best work. 

Trying to match the color of the cement between the abutment and the dental implant crown in the anterior can be very frustrating. Here’s a trick that works well for me. 

A while back I was struggling to match the color of the cement between the abutment and an anterior implant crown. I always try-in the abutment and the crown and try to confirm the shade before they are put together. We do this because the laboratory can’t redo the shade once they’ve bonded the crown and the abutment for screw retention without trying to separate the cement, which is difficult. 

Over the years, it was a challenge to replicate the opacity of the cement used to connect the titanium abutment and ceramic crown. I’ve tried using some of the opaquest try-in paste on the market. 

In the case I referred to above, we thought we had it. My lab cemented it together and I put it in. I could see the opacity of the cement through the restoration. So, we had to take it apart and try again. My laboratory technician shared with me a trick that he had learned from one of his other dentist clients. And that was to simply go to CVS, Costco, or Target and buy good old fashioned liquid white out.  

Now, I put a very tiny amount of whiteout on a micro brush and paint it on the inside of the labial surface of the crown on the intaglio surface. Then, I use a bit of translucent try-in paste to seat the crown. 

The whiteout works well because it is basically titanium dioxide and water with preservatives—the same white compound that is in super white sunscreens. In my opinion, it is relatively safe to use, and I can see what the implant will look like when the pieces are cemented together. 

How Ivoclean Works 

Lee Ann Brady, DMD 

Saliva on the inside of restoration surfaces greatly reduces the bond strength between the porcelain and the cement but during the intraoral try-in process, it is inevitable that there will be saliva contamination. 

Most dentists I know use Ivoclean from Ivoclar to clean their indirect restorations after try-in. It is an incredible material for removing saliva and other contaminants that the restoration is exposed to during the intraoral try-in process.  

We trust Ivoclean to fully remove resin or traditional cements, as well as saliva and red blood cells to produce a super pristine surface.  

Did you ever wonder how Ivoclean works to get rid of saliva and all the other debris that gets on the inside of a ceramic restoration or metal base?  

Intraoral contaminants contain lots of phosphates. Ivoclean contains suspended zirconia particles that have an affinity for phosphates. The zirconia particles pull towards them the phosphate-laden particles, so when you rinse off the Ivoclean, the intraoral debris is rinsed away leaving a clean surface. 

Note: We don’t want to expose zirconia restorations to something that contains phosphates or includes phosphoric on the label because there is a strong attraction at an elemental level between zirconia and phosphate particles. To neutralize the ionic bond between saliva phosphates and zirconia, we need an alkaline solution such as potassium hydroxide (KOH). This is the active ingredient in products such as ZirClean from BISCO. 

Dental Sleep Medicine in Restorative Practice Part 9: Marketing Dental Sleep Medicine 

By Todd Sander DDS 

How do you start reaching out to physicians and other providers to build a dental sleep medicine practice? Start with the ones you know. Start with your own personal physician and start a conversation. If your dental patient is on CPAP, get permission to converse with their doctor. I spend time contacting many primary care doctors and find they are the ones who know patients are non-compliant with their CPAP therapy. They help me get patients re-evaluated by a sleep specialist. 

This may not be true in your community, but in Charleston, SC, where I practice, many primary care doctors don’t know what to do with their non-compliant CPAP patients. They are thrilled to have someone to refer them to try alternative therapy. 

Years ago, I reached out to sleep testing centers to communicate my services. Both independent sleep labs and hospital-based sleep labs have been great sources of referrals. For many years, I was the dental advisor to a sleep lab. A great conversation starter with sleep physicians, is the potential of combining CPAP and an oral appliance. This often allows the CPAP air pressure to be turned down so their patients be more comfortable and compliant. 

When you screen your dental patients for airway issues such as sleep apnea and snoring, the next step is referring your patients with issues for a sleep study. When the patient discusses their symptoms with their primary care physician or a sleep physician, you are mentioned and often documented as making the referral. Over time, physicians come to know you as a go-to provider of dental sleep appliance therapy. This process is sped up when you take the time and initiative to contact your patient’s primary care physician with your patient’s permission. You can guide physicians and remind them of the recommended standards-of-care, including appliance therapy in place of or in combination with CPAP therapy. 

Some patients self-refer to me, as friends and family talk about their experiences in my office, but I am not spending money on digital advertising to bring in dental sleep medicine patients. Mostly, they are referred to me by physicians, dentists, and other patients.  This is the same for my dental practice. 

As mentioned in a previous part of this series, our hygienists have attended dental sleep medicine courses with me and screen for airway issues. They adeptly educate and guide patients who have signs and symptoms to schedule an examination and consultation with me. 

Note: When patients are referred to me for dental sleep medicine, I never encourage them to become dental patients in our practice. This is a choice they might make but I am extremely careful to refer patients referred by a dentist back to their referring dentist for all dental needs. I am an adjunct to help other dentists’ patients fulfill a prescription for a dental appliance. 

If a patient comes in for sleep-disordered breathing but is also experiencing facial pain or TMD, I understand that this patient’s two issues are likely connected and I will not be able to successfully treat one without treating the other. This is an opportunity to communicate in depth with the referring dentists and let them know I plan to treat the patient for both issues simultaneously. This has been easier for me to do because I have had years of experience in treating facial pain and TMD issues in my dental practice, as well as sleep apnea and snoring.